(a) (d) (b) (e) 1. part no. expression : (b) dimension code (c) type code (a) series code 2. configuration & dimensions : a superworld electronics (s) pte ltd 3. schematic : (d) inductance code : 1r0 = 1.0uh (e) tolerance code : m = 20%, y = 30% pg. 1 8.50.3 b c 2.80.2 d 4.70.3 e unit:m/m 9.50.3 1.40.30 (c) (f) (f) f : rohs compliant 1r0 a b c d e 4. materials : p i c 0 8 0 3 h p 1 r 0 m f - (a) core (b) wire (c) teminal (d) ink (e) paint 03.11.2015 smd power choke coil pic0803hp series (g) (g) 11~99 : internal control number note : specifications subject to change without notice. please check our website for latest information. 1236 l h g recommend pc board pattern g 4.5 h 10.4 l 5.2
superworld electronics (s) pte ltd pg. 2 6. electrical characteristics : inductance l part no. pic0803hp1r0mf 0 1.00 ( h ) @ 0 a 7.0 dcr typ. @ 25c ( m ) irms ( a ) 14 29 ( a ) isat typ. typ. g) part temperature (ambient+temp. rise) : should not exceed 125c under worst case operating conditions. e) heat rated current (irms) will cause the coil temperature rise approximately t of 40c (keep 1min) f ) saturation current (isat) will cause l0 to drop 20%. 5. general specification : c) storage temp. : -40c to +125c b) operating temp. : -40c to +125c a) test freq. : l : 100khz/1.0v dcr ( m ) max. @ 25c 8.1 2.20 18 9 21 20.5 3.30 23 8 14 27 4.70 32 7 11 37 6.80 46 5.5 9 53 15.0 88 3.8 7 102 smd power choke coil note : specifications subject to change without notice. please check our website for latest information. 10.0 65 4.7 8.2 75 8.20 52 5 8.5 60 pic0803hp series 03.11.2015 pic0803hp2r2mf pic0803hp3r3mf pic0803hp4r7mf pic0803hp6r8mf pic0803hp8r2mf pic0803hp100mf pic0803hp150mf pic0803hpr47mf 0.47 3.0 21.5 35 3.4 PIC0803HPR33MF 0.33 2.3 25 37 2.6 pic0803hpr22mf 0.22 1.46 30 45 1.61 pic0803hp1r5mf 1.50 10.2 11.5 24 11.8 h) storage condition (component in its packaging) i) temperature: -10 to 40c ii) humidity : 60%rh d) humidity range : 85 3% rh tolerance code : m = 20%, y = 30%
superworld electronics (s) pte ltd pg. 3 7. characteristics curves : smd power choke coil note : specifications subject to change without notice. please check our website for latest information. pic0803hp series 03.11.2015 pic0803hpr22mf PIC0803HPR33MF pic0803hpr47mf pic0803hp1r0mf pic0803hp1r5mf pic0803hp2r2mf
superworld electronics (s) pte ltd pg. 4 smd power choke coil note : specifications subject to change without notice. please check our website for latest information. pic0803hp series 03.11.2015 pic0803hp3r3mf pic0803hp4r7mf pic0803hp6r8mf pic0803hp8r2mf pic0803hp100mf pic0803hp150mf
superworld electronics (s) pte ltd pg. 5 8. soldering : c) never contact the ceramic with the iron tip e) use a 20 watt soldering iron with tip diameter of 1.0mm d) 1.0mm tip diameter (max) f) limit soldering time to 4~5 secs. 8-1.2 soldering iron (figure 2) : in the event that a soldering iron must be employed the following precautions are recommended. products attachment with soldering iron is discouraged due to the inherent process control limitations. recommended temperature profiles for re-flow soldering in figure 1. mildly activated rosin fluxes are preferred. the minimum amount of solder can lead to damage from the stresses caused by the difference in coefficients of expansion between solder, chip and substrate. our terminations are suitable for all re-flow soldering systems. if hand soldering cannot be avoided, the preferred technique is the utilization of hot a) preheat circuit and products to 150c. air soldering tools. 8-1.1 solder re-flow : note : b) 355c tip temperature (max) 8-1. soldering temperature c over 1min. gradual cooling within 4-5s 350 150 preheating soldering cooling natural time(sec.) 60~150s 20~40s soldering temperature c 480s max. 60~180s 150 25 tp(260c/40s max.) 217 200 preheating cooling natural figure 1. re-flow soldering: 3 times max. figure 2. iron soldering: 1 times max. smd power choke coil note : specifications subject to change without notice. please check our website for latest information. pic0803hp series 03.11.2015
superworld electronics (s) pte ltd pg.6 smd power choke coil note : specifications subject to change without notice. please check our website for latest information. pic0803hp series 03.11.2015 9. packaging information : b1(mm) 10.10.1 9-3. packaging quantity pic0803 series bo(mm) 9.00.1 16.00.1 p(mm) ao(mm) 8.90.1 ko(mm) 3.30.1 240.3 w(mm) 9-2 tape dimension 24.4+2.0/-0 a(mm) 13" x 24mm type 1002 b(mm) d d(mm) 13.50.5 330 c(mm) embossed carrier b a cover tape 9-1. reel dimension pic0803 8000 2000 carton chip / reel inner box size 1000 2.00.5 ?c 11.50.1 f(mm) 0.350.05 t(mm) 1.50.1 d(mm) d/c d/c d/c d/c 1r0 d/c 1r0 1r0 1r0 1r0 4.0 2.0 p t
superworld electronics (s) pte ltd 9-4. tearing off force the force for tearing off cover tape is 10 to 130 grams in the arrow direction under the following conditions. a) products should be handled with care to avoid damage or contamination from perspiration and skin oils. 1. storage conditions : to maintain the solderabililty of terminal electrodes : a) recommended products should be used within 12 months from the time of delivery. b) the packaging material should be kept where no chlorine or sulfur exists in the air. b) vacuum pick up is strongly recommended for individual components. c) bulk handling should ensure that abrasion and mechanical shock are minimized. 2. transportation : application notice top cover tape f base tape 165 to 180 room temp. (c) 5~35 room humidity (%) 45~85 tearing speed (mm/min) 300 room atm (hpa) 860~1060 pg. 7 (referenced ansi/eia-481-c-2003 of 4.11 standard) smd power choke coil note : specifications subject to change without notice. please check our website for latest information. pic0803hp series 03.11.2015
|
